bczee
02-04-2009, 07:23 PM
I have kept a running sheet of Tools that I have both used and research for the Correct tool to be using on the Gen III and IV engines.
I hope that this list might help others. If you have other, please forward the Name, Part number and Company that makes it:
Tools for Gen III/IV engines
Kent Moore Gen III Engine Took Kit - #J43145, Includes all required tools (per what the say)
Valve Lifters –
• JPR #99-JPR-CIT ($95.00)
• 5/16 wood or steel rods
Balancer / Pulley Services Tools
• Balancer Puller –
Snap-On #YA6490, ($130.00 ?)
Any late model GM/Chrysler Harmonic puller
Three Jaw Puller
Astro #7822 (has holder tool incl, $70.00)
• Balancer Installer –
GM – J41665 Crankshaft Balancer and Sprocket Installer
Snap On Set YA188E
• Balancer/Pulley Holder –
Snap On YA6470
Summit Racing #SME-906008
• Balancer Pinning Kit –
ATI Crakshaft / Balancer ATI #918993 ($150.00)
Torque Angle Gauge
• Snap On Torque Angle Gauge ½” TA360
• Snap On Torque Angle Gauge 3/4” TA362
Front / Rear Cover Alignment Tool –
• GM J41476
Power Steering & Alternator Pulley –
• Snap On Power Steeting/Alternator Pulley Puller CJ117C
• Snap On Power Steering Pulley Installer CJ122
• Astro #7874
• Astro #7847
Oil Pressure Sensor Socket –
• Snap-On A120
• Deep 27mm or a 1 1/16” Deep socket, 2.5 deep
Leak down Tester
• Snap On EEPV309A
Vavle Springs Compressor -
• Crane - #99472-1 ($125.00 ?)
• Lingenfelter - #800-290 ($130.00)
• Snap On YA3271
• Snap On VST100
• Snap 0n S6121
Fuel Quick Disconnect -
• Lingenfelter #KMJ-41769
• Lisle #37500 or #35000
• KD # 3321
• Snap On Fuel Module Disconnect FIH500
• Snap On Set Fuel Line Coupling Release FIH9055
Injector Harness Tester (NOID Light)
• Snap On Kit FID8838A (kit of 8 lights)
Clutch / Flywheel
• Flywheel Turner / holder
KENT MOORE (GM) J-42386-A (Flywheel Holding Tool).
Snap On Flywheel Turner A144A
• Clutch Aligner
Snap On set A37M
Snap On set A145
• Clutch Disconnect
Same as Fuel disconnect tools
• Pilot Bearing Puller
Snap On SP2031
Tool Sources:
GM
Crane
Lingenfelter
ATI
Kent Moore
Snap on
Mac Co
Lisle
Astro
KD
eBay
I hope that this list might help others. If you have other, please forward the Name, Part number and Company that makes it:
Tools for Gen III/IV engines
Kent Moore Gen III Engine Took Kit - #J43145, Includes all required tools (per what the say)
Valve Lifters –
• JPR #99-JPR-CIT ($95.00)
• 5/16 wood or steel rods
Balancer / Pulley Services Tools
• Balancer Puller –
Snap-On #YA6490, ($130.00 ?)
Any late model GM/Chrysler Harmonic puller
Three Jaw Puller
Astro #7822 (has holder tool incl, $70.00)
• Balancer Installer –
GM – J41665 Crankshaft Balancer and Sprocket Installer
Snap On Set YA188E
• Balancer/Pulley Holder –
Snap On YA6470
Summit Racing #SME-906008
• Balancer Pinning Kit –
ATI Crakshaft / Balancer ATI #918993 ($150.00)
Torque Angle Gauge
• Snap On Torque Angle Gauge ½” TA360
• Snap On Torque Angle Gauge 3/4” TA362
Front / Rear Cover Alignment Tool –
• GM J41476
Power Steering & Alternator Pulley –
• Snap On Power Steeting/Alternator Pulley Puller CJ117C
• Snap On Power Steering Pulley Installer CJ122
• Astro #7874
• Astro #7847
Oil Pressure Sensor Socket –
• Snap-On A120
• Deep 27mm or a 1 1/16” Deep socket, 2.5 deep
Leak down Tester
• Snap On EEPV309A
Vavle Springs Compressor -
• Crane - #99472-1 ($125.00 ?)
• Lingenfelter - #800-290 ($130.00)
• Snap On YA3271
• Snap On VST100
• Snap 0n S6121
Fuel Quick Disconnect -
• Lingenfelter #KMJ-41769
• Lisle #37500 or #35000
• KD # 3321
• Snap On Fuel Module Disconnect FIH500
• Snap On Set Fuel Line Coupling Release FIH9055
Injector Harness Tester (NOID Light)
• Snap On Kit FID8838A (kit of 8 lights)
Clutch / Flywheel
• Flywheel Turner / holder
KENT MOORE (GM) J-42386-A (Flywheel Holding Tool).
Snap On Flywheel Turner A144A
• Clutch Aligner
Snap On set A37M
Snap On set A145
• Clutch Disconnect
Same as Fuel disconnect tools
• Pilot Bearing Puller
Snap On SP2031
Tool Sources:
GM
Crane
Lingenfelter
ATI
Kent Moore
Snap on
Mac Co
Lisle
Astro
KD
eBay